Home>CPAP Interfaces>Full Face CPAP Interfaces > ResMed AirTouch F20 Memory Foam Full Face CPAP Interface with Headgear

ResMed AirTouch F20 Memory Foam Full Face CPAP Interface with Headgear

See Details

If you are purchasing a new CPAP, Auto CPAP or BiLevel (BiPAP) machine, humidifier or an oxygen concentrator, then federal law requires that we receive a copy of a prescription written by your doctor. A sleep study report does not qualify as a prescription. Also, the purchase of complete CPAP masks does require a prescription. (* Note that the component parts that make up the mask DO NOT require a prescription! *)

The prescription must state that it is for CPAP therapy and at what pressure your machine should be set. If you are purchasing a standard CPAP machine (one that operates at a constant pressure), then the prescription must show one pressure setting, which is generally a number between 4 and 20 and measured in cm of H2O. If you are purchasing an Auto CPAP machine, then your prescription must state two different pressures: A low (minimum) pressure setting and a high (maximum) pressure setting. If you are purchasing a BiLevel machine, then your prescription must state two pressure settings: An inspiratory (IPAP) setting and an expiratory (EPAP) setting. If you are purchasing an Oxygen Concentrator, the prescription should have the flow rate stated in Liters per minute.

Prescriptions can be faxed to us at 888-469-2555, or we can accept a scanned copy of your prescription by emailing it to us at [email protected].

Please note that orders for machines, concentrators, or complete masks will NOT be shipped until we receive a copy of your prescription!

ResMed AirTouch F20 Memory Foam Full Face CPAP Interface with Headgear

For Him with Blue and Gray Straps

Part ID:

AirTouch F20

In Stock

| Questions about this item? Ask here.

(See 5 Questions)

Your Price:$115.00

6 Review(s)

Sizing

Small (Blue Straps) - 63000

Medium (Blue Strap) - 63001

Large (Blue Strap) - 63002

Small For Her (Lavender Strap) - 63003

Medium For Her (Lavender Straps) - 63004

How will you send your Prescription?

I will send my prescription via email

I will send my prescription via fax

A copy of my prescription is on file

Send me the parts kit (no Rx Req)

Quantity

U.S. Sales Only

Manufacturers Note:

The new ResMed AirTouch F20 UltraSoft memory foam cushion represents a breakthrough in patient comfort. The permeable foam creates a breathable seal that reduces facial markings and skin irritation. Like the AirFit F20 (which shares the same frame and headgear), the AirTouch features magnetic clips, a quick-release swivel elbow, and simple design that makes it fast and easy to put on as well as clean and reassemble.

This is one of the best sealing full-face interfaces that we have seen. It can hold a seal to pressure settings up to 25 cm/h2o, and it is a very effective solution for men with facial hair. The suppleness of the memory foam cushion allows it to hug the contours of your face like a custom fit, which also helps to reduce those red pressure marks that a lot of us have to live with in the morning. However, this exceptional comfort does come with a cost - the recommended replacement interval for these cushions is 30 days, and under no circumstances should water or liquid cleaning products be used on the cushion - otherwise the memory foam will become saturated, which will ruin the cushion. Instead, we recommend wiping the surface of the cushion with a damp cloth or a cleaning wipe.

Product Features:

Designed to reduce facial markings and skin irritation – even when sealed firmly against the skin – AirTouch fits 98% of patient faces.
The permeable foam creates a uniquely natural, breathable seal that allows some excess heat and sweat to escape through the cushion without compromising therapy pressure.
Compatible with any CPAP, including the world’s smallest CPAP, ResMed’s new AirMini.
Easy to maintain and designed to seal at a range of therapy pressures, and to fit the same frame as the AirFit F20, which uses the InfinitySeal silicone cushion – so patients can easily try and choose the material they prefer best.

What's in the Box

ResMed AirTouch F20 Full Face CPAP Interface with UltraSoft memory foam cushion
Headgear
Printed users manual
Quick Fitting guide and part number listing

Title?

other full-face masks were too rough on the bridge of my nose, leaving me with red marks and sometimes blisters. I was really hopeful this mask would be an exception, but after a few days of use, the blisters are back on the bridge of my nose.

Did you find this helpful? 13 of 15 Found Helpful

Reviewed by: Doug from TN. on 6/26/2018

AirTouch F20 life

This was the most comfortable CPAP mask I have worn. Unfortunately, the foam tears around the bridge of the nose. The first AirTouch F20 lasted 27 days which wasn't too bad. The second tore after 5 days. I have had to switch masks as these don't last long enough for the price.

Did you find this helpful? 10 of 11 Found Helpful

Reviewed by: Tom from MI. on 8/13/2018

It leaks too much

I was very hopeful this would be what I needed. Unfortunately, I had a terrible air leak issue around the seal, so I had to tighten down the harness so much it was very uncomfortable.

Did you find this helpful? 1 of 2 Found Helpful

Reviewed by: Theodore from Southwest Ranches. on 6/20/2019

Colorado

Love this mask! In fact, ordered two more immediately to be sure I'm always covered. :)

Did you find this helpful? 1 of 2 Found Helpful

Reviewed by: Jerry from Colorado Springs. on 1/14/2019

Excellent

Able to breath from mouth and relax jaw. Nice for those with those issues. The product itself is outstanding.

Did you find this helpful? 1 of 2 Found Helpful

Reviewed by: Ivan Canino from Hialeah . on 11/3/2018

waist the money -garbage

Did you find this helpful? 1 of 5 Found Helpful

Reviewed by: bogumil from usa. on 10/10/2018

Q: Is the sizing on this mask the same as the airfit 10?, I have a med but feel it is a little large, the other ? Is, can you change mask sizes w/o having to change the head gear? Do you take insurance?

Asked by: Bruce - 9/9/2018

A: The F10 and F20 are different masks so the parts will not interchange with each other. You can't put the F20 cushion on a F10 mask frame. The F20 frame is the same for all three sizes so if you have a medium you can change sizes by just replacing the cushion with a small or large. We do not bill any insurance plans

Was this answer helpful? 2 of 3 Customer(s) found this Answer helpful.

Answer provided by: Tony Ward (9/10/2018)

(Submit an answer)

Q: Can this mask be cleaned in a SoClean sanitizer?

Asked by: Jim - 8/29/2018

A: We don't sell the SoClean so I would recommend you check with them first. That being said I think it would be fine. You can't get the memory foam wet so ResMed recommends you wipe the cushion off with an alcohol-free wipe each day.

Was this answer helpful? 1 of 2 Customer(s) found this Answer helpful.

Answer provided by: Tony Ward (8/29/2018)

(Submit an answer)

Q: Are the foam face seal replaceable, or us it part of the mask?

Asked by: Bruce - 9/9/2018

A: Yes, you can replace the cushions on this mask but the foam is attached to the plastic shell so you replace that portion as well. The part numbers are 63028, 63029, and 63030.

Was this answer helpful? 1 of 2 Customer(s) found this Answer helpful.

Answer provided by: Tony Ward (9/10/2018)

(Submit an answer)

Q: Is the memory foam latex free?

Asked by: Heidi - 11/22/2018

A: I can't find a latex statement on the product itself but customer service at ResMed says it is latex free.

Was this answer helpful? 0 of 1 Customer(s) found this Answer helpful.

Answer provided by: Tony Ward (11/26/2018)

(Submit an answer)

Q: Does this mask discharge air from the Top or bottom?

Asked by: Vernon reid - 11/21/2019

A: The air vents around the circular portion of the elbow on the front of the mask so it's pretty much every direction. These masks have ResMeds QuietAir vent so it's very subtle compared to most mask.

Was this answer helpful? 0 of 1 Customer(s) found this Answer helpful.

Answer provided by: Tony Ward (11/25/2019)

(Submit an answer)